Skip to main content

Custom PCB & Electronic Module Design Services – From Concept to Production


Industrial Electronics Design for Automation, Sensors, and Embedded Systems

We design and build custom electronic modules and sensor interface boards for industrial, automation, research, and embedded system applications.
If you have an idea for a sensor module, control board, or electronic device, we can help you turn it into a working product — from circuit design and PCB layout to prototype development and testing.
Modern sensor modules are widely used in automation, robotics, environmental monitoring, and industrial control systems to measure parameters like temperature, pressure, vibration, and humidity.

  • Industrial grade designs
  • Complete schematic + PCB + firmware
  • Small and bulk production support


We develop reliable electronic modules tailored to your application requirements.

Sensor Interface Modules
  • PT100 / RTD temperature sensor interfaces
  • Thermocouple signal conditioning modules
  • Humidity and environmental sensor boards
  • Vibration and motion sensing modules
  •  Pressure sensor interfaces
Industrial Signal Modules
  • 4–20mA signal transmitters
  • 4–20mA to voltage converters
  • Analog signal conditioning circuits
  • Industrial analog input/output modules
Embedded Control Boards
  • Microcontroller-based control systems
  • Data logging modules
  • Wireless sensor nodes
  • Automation control boards
Power & Interface Circuits
  • Industrial power supply circuits
  • RS485 / Modbus communication modules
  • Relay driver boards
  • Motor and actuator control circuits
Professional Schematic and PCB design with Optimized signal routing ,EMI and noise reduction practices. Complete schematic,PCB, GERBER for production or full working prototype will be provided. 

ORDER VIA FIVERR  = Connect OptimElectronic

OR

GET INSTANT QUOTE

Labels:

Comments

Post a Comment

Popular posts from this blog

HP Pavilion 15 (hp 15bw504ax) no display repair - LA-E841P main board

In this repair case, a customer brought an HP Pavilion 15 laptop that was completely dead with no power indication. The laptop did not respond when the power button was pressed, and there were no charging or status LEDs. After opening the laptop and removing the bottom cover, I began troubleshooting by checking the main power input connector on the motherboard. When the power adapter was connected, the adapter initially supplied 19V, but the voltage immediately dropped to 0V. This behavior typically indicates that the main 19V rail is shorted on the motherboard. When such a short circuit exists, the adapter’s protection mechanism shuts down the output to prevent damage. Diagnosing the Short Circuit To locate the source of the short, I performed a standard motherboard diagnostic procedure by measuring the resistance between ground and the main power inductors. During this test, one of the inductors showed a direct short to ground. Further investigation revealed that this inductor belong...
Post a Comment
Read more

How to wire long distance RS485 cables without communication errors

In industrial environments, long-distance signal wiring such as RS485 must be installed carefully to avoid electrical noise, signal distortion, and false triggering. Factories usually contain motors, VFDs, contactors, and high-current cables that can generate strong electromagnetic interference (EMI). Following proper wiring practices ensures reliable and stable signal transmission. Below are the best practices used in industrial automation systems. 1. Use Twisted Pair Cables For long-distance signal transmission, always use twisted pair wires. Twisting the wires helps cancel electromagnetic interference induced by nearby cables.  For RS485 systems, cables similar to Cat5/Cat6 network cable work very well. 2. Use Shielded Cable in Noisy Environments Factories usually have electrical noise from, VFD drives Large motors Welding machines Switching power supplies Using shielded cables prevents noise from entering signal lines. Important rule -  Connect the shield to ground at only...
Post a Comment
Read more

Installing a push button in a electrically noisy environment

Installing a push button over a long distance in a noisy factory environment (motors, contactors, VFD drives, welding machines, etc.) requires proper wiring practices to prevent false triggering, signal noise, and unreliable operation. Below are the industrial best practices used in automation and control systems. 1. Use 24V Industrial Control Voltage For long-distance push buttons, avoid using 5V or logic-level signals.  Factories usually use 24V DC control signals because they are more resistant to electrical noise. Typical wiring : +24V  -> Push Button -> PLC Input / Controller Input Advantages, Better noise immunity Standard in industrial automation Compatible with PLC inputs 2. Use Twisted Pair Cable Long signal wires should use twisted pair cable. it r educes electromagnetic interference (EMI),  Improves signal reliability and m inimizes induced noise from nearby cables 3. Use Shielded Cable In noisy factories with motors or VFD drives, use shielded twisted pa...
Post a Comment
Read more